Showing posts with label efficiency. Show all posts
Showing posts with label efficiency. Show all posts

Saturday, September 12, 2009

Why HVAC Isn’t Just a Lot of Hot Air (or Cold, Either)

Ever since I started my career in the construction industry, I have always seemed to run into problems with HVAC systems. This shouldn’t be that surprising, since the HVAC system is the primary system responsible for the living conditions in your home and can have the most impact on how a building functions. I have seen systems that are contaminated with fungal growth, systems that you would think had been installed to provide irrigation to the crawlspace, systems that my 8 -year-old niece and nephew could have installed, and systems that are a piece of art. However, out of all of these, the latter is the rarest of them all.

In the past year, I have dealt with systems that
  • increased the gas bill after the system was installed,
  • caused the homeowner to pay more per month than they were per season before it was installed,
  • were not cooling or heating the home equally. The excuse for this was that two systems should have been installed, when the contractor installed only one - however, that one unit was not properly installed (twice), and ended up causing damage to the ductwork.
These are only three of the multitude of cases where I have seen of improperly sized, installed, or designed units. Why is this? The only explanation I can come up with is that homeowners - and unfortunately, most HVAC technicians - do not understand the impact the system can have on the home, and that it is not as simple as a fan moving air through some round tubes.

There is a standard of practice set forth in both the building code and by industry organizations that state how a system should be designed. This process takes into account how each component of the system works with the other, and combines them to provide efficient delivery of your conditioned air. This whole process starts with what is called a load calculation, or Manual J calculation. This takes into account the construction of your home and how heat is transferred between the exterior walls, ceiling, floor and the exterior environment. The next step covers the system selection or Manual S. This outlines the proper method to select a system to accommodate for the required load calculations. Next comes Manual D, which is another critical step as this is the duct design. Each system must have the ducts designed for the unit to be installed. Finally is Manual T, which is the register and grill sizing. Even grill sizes can impact your comfort levels!

Properly designed systems can increase your comfort and decrease the cost of your utilities. Next time you are going to have your HVAC system replaced, take note of these simple reminders, and hopefully, you will have your system properly installed:

1. Make sure Manual J, S, T, and D calculations were performed for your system.
Of all of these, Manual J and D are the most critical. Whether you are having your home system replaced (ducts and system) or just the unit, these calculations are critical. There is no such thing as rules of thumb or matching the system with what you previously had. Each home is unique, and the system you had before may have been improperly sized.

2. Your ducts impact your system’s efficiency.
While most people will try to just install a new unit and keep using the old duct work, this can actually cost you money. If ducts are improperly sized for the system, they can cause the system to operate inefficiently. Why pay for the more efficient system if it is going to operate at a lower efficiency than the one you just replaced?

3. Manual J has safety factors already figured in.
There are some companies that will perform Manual J calculations, but they will not use the weather data provided in the back. Instead, they will design the system for hotter temperatures. You don't design systems for newsworthy days! By raising the design temperature, you oversize the system. When you do this, you size the system for 1% of time it is in operation - and oversizing for 99% of the time.

4. The lowest or highest price may not be the best.
It's hard to judge an install on just the price of the system. HVAC installs can vary greatly! ACCA (Air Conditioning Contractors of America) has produced a document that allows you to compare bids so that you get the best value. However, remember that if the contractor doesn’t properly design the system, it doesn’t matter how good their price is! You can get the document here: Quality Installation Specifications


Do NOT Install Replacement Windows!

The tip this week is more of a what not to do instead of a what to do. Every day, I see a commercial advertising replacement windows and how much money they can save you; and every day, I know someone has invested a lot of money into their home that they will not get paid back.

Many people are advertising 50% savings with the replacement of new windows. This is completely true. You may save 50% on the amount of energy the windows cost you, but this translates to only about 10% to 15% of your total bill. With this limited savings as compared to the cost of the windows, you end up with a very long payback period. If 10 windows cost you between $6000 and $7000 and you save a gratuitous 20% on a utility bill of $200, your payback will be between 12 and 15 years. This is almost a best-case scenario. In most cases, the paybacks for replacement windows are going to be between 20 and 30 years, because the savings will not be that great for such a small investment.

Most homeowners are not going to be in the home for 15 years, and if they are, there are several other items that can be done to the home that have a quicker payback. I will only recommend replacement windows in extreme cases. In the majority of the homes I see, I would more likely recommend installation of storm windows (for single panes), or repair of the windows currently in place, typically because those are the best scenarios when windows are involved. So next time you have someone suggest you replace your windows or you see the commercials, remember that those windows will save you money, you are better off investing in other, similarly effective improvements that have a much shorter payback period.

Saturday, August 29, 2009

Welcome to the E3 Building Concepts Blog!

Since this is the first blog from E3, I feel that it is only fitting to introduce the company. First and foremost, what does E3 stand for? It stands for Building Elements, Environment, and Efficiency. These are the three key components of any building that work together to provide us a comfortable, affordable and safe living and working space. E3 is a consulting firm based in building science that understands how each and everyone of these components work together. Our services currently include indoor air quality investigations, green/sustainable consulting and verification, energy audits and Energy Star verification.

While many companies are popping up around the area providing one or more of these services, I assure you that E3 you will provide the most professional, educated, and thoughtful service each and every time. As the owner, I have been in the construction and building science industry since 2002 and have worked on projects of various sizes investigating and correcting issues with the building environment -- well before energy efficiency and "green" became a catchphrase! I have attained multiple professional certifications and hold a Bachelor's degree from N.C. State that all benefit me in my daily work with building science.

Each week I will post my thoughts, knowledge, and opinion on related items and events, as well as a new recommendation for reducing the energy consumption of your home. I hope you will find this blog helpful and insightful in an ever changing industry!


Cut off ceiling fans when you are not in a room!!!

This is one item that I constantly go over with individuals in an energy audit. A ceiling fan is a great way to help reduce your cooling cost in the summer time, but only if you are in the room with the ceiling fan! Ceiling fans cool the person, not the room, by air movement across your skin. The air movement generated by the fan causes you to cool down, not the room. If you leave the fan on when you are not in the room, you are actually generating heat through the motor and wasting electricity. Below are two thermal images showing the heat generated by the motor. The image on the right is blended so that you can see more of the fan. The room temperature is 78 and 80 degrees at the ceiling. You can see that the fan motors are 139 and 130 degrees. This is adding an ample amount of heat to these rooms and not cooling anything down. So next time you leave a room, remember to not only cut off the lights but the fan too!